AT Aquatic Mech

About AT Aquatic Mech

AT Aquatic Mech (4789-1) is a LEGO LEGO set released in 2002, currently averaging $95.00 used on BrickLink. It comes with 1 minifigure worth a combined $2.20. The set has retired from retail, so secondary market is the only option. The full parts inventory runs 77 pieces.

Part-out value

The minifigures make up only 2% of this set's value ($2.20 out of $95.00). The bulk of the value is in the parts or the set being complete. Sell it as a complete set if possible.

Seller notes

• This is a vintage set (2002). Condition of the box and instructions significantly affects value. A complete set with original box and instructions can sell for well above the average.

Minifigures in AT Aquatic Mech (1)

Dash - Mission Deep Sea, Trans-Dark Blue Visor

alp034$2.20

Parts (77)

Brick 2 x 2 Corner

×2

Tile, Modified 1 x 2 Grille with Bottom Groove

×4

Wedge, Plate 3 x 6 Cut Corners

Plate 2 x 2 Corner

×2

Minifigure, Visor Standard

Tile, Modified 2 x 2 with Pin

×4

Plate, Modified 2 x 2 with Pin on Bottom, Small Holes in Plate and Locking Fingers on Underside

×2

Shark Body

Minifigure Footgear Flippers, 2 on Sprue

Technic, Pin with Short Friction Ridges

×2

Hinge Train Gate 2 x 4

Brick 2 x 4

Brick 2 x 2

×2

Brick 1 x 2

×4

Brick 1 x 6

Plant Sea Grass / Seaweed

Minifigure, Utensil Binoculars Town

Plate 2 x 4

×4

Plate 2 x 4

×4

Plate 2 x 3

×2

Plate 2 x 2

×3

Plate 1 x 2

×8

Plate 1 x 2

×4

Brick, Modified 1 x 2 with Bar Handle on Side

×3

Brick, Modified 1 x 2 with Split U Clip Thick (Vertical Grip)

Plate 2 x 8

Slope 45 2 x 2

Hinge 1 x 2 Locking with 2 Fingers and Tow Ball Socket

Arm Grabber Angled

×2

Slope, Curved 2 x 2 Lip with Black 'TEE VEE', Green 'MISSION DEEP SEA', and Silver Buttons Pattern

Minifigure, Hair Flat Top with Extended Sides

Brick, Round 1 x 1

×4

Technic, Axle and Pin Connector Angled #1

Technic, Pin 3L with Friction Ridges and Stop Bush

Technic, Axle 2L Notched

Technic, Liftarm Thick 1 x 7

×2

Arch 1 x 4

Slope, Inverted 45 2 x 2 with Flat Bottom Pin

×3

Technic, Pin without Friction Ridges

×2

Slope 65 2 x 2 x 2 without Bottom Tube

×2

Technic, Brick 1 x 4 with Holes

×2

Plate, Modified 1 x 2 with 1 Stud without Groove (Jumper)

Plate, Modified 1 x 2 with Bar Handles - Flat Ends, Low Attachment

Plate, Round 2 x 2 with Axle Hole

Plate, Round 1 x 1

×11

Plate, Modified 1 x 1 with Light Attachment - Thick Ring

×2

Plate, Modified 1 x 1 with U Clip Thick (Vertical Grip)

×4

Slope, Curved 4 x 1 Double with 2 Recessed Studs

Tile, Round 2 x 2 with Fine Mesh Grille Manhole Cover Pattern

×2

Support Foot Platform with Black Danger Stripes and Silver Hose Pattern on Both Sides (Robot Diver)

×2

Propeller 8 Blade 5 Diameter

×2

Cylinder 4 x 4 x 1 2/3 with Pin Holes and Center Bar

×2

Hinge Cylinder 1 x 3 Locking with 1 Finger and Pin with Round Hole and Friction Ridges on Ends

Technic, Brick Modified 2 x 2 x 2 with Rotation Joint Socket

×2

Ladder 1 1/2 x 2 x 2

×2

Rubber Band / Belt Holder 2 x 4 x 2 1/3

Plate, Modified 2 x 2 with Vents

×2

Windscreen 6 x 4 x 2 Wedge Curved

Slope, Curved 6 x 1 with 2 Studs with Black Danger Chevrons and Silver Hose Pattern

×2

Hinge Plate 1 x 4

Container, Box 2 x 2 x 2

×2

Container, Box 2 x 2 x 2 Door with Slot

×2

Technic, Axle 3L

Antenna Small Base with Black Lever (4592 / 4593)

×3

Plate, Modified 1 x 2 with Bar Arm Up (Horizontal Arm 6mm)

×3

Bar 1 x 3 with Clip and Stud Holder (Robot Arm)

×2

Wedge 6 x 4 Triple Inverted with Connections between 2 Studs

Wedge, Plate 3 x 4 without Stud Notches

×2

Plate, Modified 1 x 1 with U Clip (Horizontal Grip)

×2

Plate, Modified 1 x 1 with U Clip (Horizontal Grip)

×4

Propeller 3 Blade 3 Diameter with Axle Hole

×2

Bracket 5 x 2 x 2 1/3 with 2 Holes

×2

Bar 1 x 4 x 2

×2

Rubber Band Extra Small (Square Cross Section)

×4

Minifigure, Utensil Stretcher Holder Flexible

×2

Technic Rotation Joint Ball with Arm and Black Pin and Socket Ends

×4

Shark Head Sawfish with Debossed Eyes

Common questions about AT Aquatic Mech

Explore more