Plate, Modified 2 x 2 with Pin Hole - Full Cross Support Underneath
×2Brick, Modified 1 x 2 with Studs on 1 Side
×5Bracket 5 x 2 x 1 1/3 with 2 Holes and Bottom Tube
×2Slope, Curved 2 x 1 x 2/3
×2Slope, Curved 2 x 1 x 2/3
×2Slope, Curved 2 x 1 x 2/3
×6Wheel 18mm D. x 8mm with Fake Bolts and Deep Spokes with Inner Ring
×2Plate, Modified 1 x 2 with Tow Ball on Side
×2Panel 1 x 4 x 2 with Side Supports - Hollow Studs
×2Tile, Round 2 x 2 with Bottom Stud Holder with Fine Mesh Grille Manhole Cover Pattern
×2Slope, Curved 2 x 2 x 2/3
×28Plate, Modified 1 x 2 with 1 Stud with Groove and Bottom Stud Holder (Jumper)
×4Tile, Modified 1 x 1 with Open O Clip
×2Plate, Modified 1 x 2 with Pin Hole on Bottom
×4Tile, Modified 1 x 2 Grille with Bottom Groove
×6Tile, Modified 1 x 2 Grille with Bottom Groove
×10Wedge, Plate 3 x 6 Cut Corners
Hinge Plate 1 x 4 Swivel (2429 / 2430)
×2Wedge, Plate 3 x 3 Cut Corner
×4Wedge, Plate 3 x 3 Cut Corner
×8Technic, Pin with Short Friction Ridges
×11Brick, Modified 2 x 2 with Pins and Axle Hole
Plate, Modified 2 x 4 with Pins and Thin Angled Supports
×2Brick, Modified 1 x 2 with Bar Handle on Side
×2Wedge, Plate 12 x 6 Left
×2Wedge, Plate 12 x 6 Right
×2Plate, Round Corner 3 x 3
×2Slope 45 2 x 2 with Silver Control Panel and Screen Pattern
Brick, Modified 1 x 4 with Studs on Side
×2Tile 1 x 2 with SW Avionics Control Panel with Copper, Red and Silver Display and Buttons Pattern
×3Technic, Axle and Pin Connector Angled #5 - 112.5 degrees
×2Technic, Brick 1 x 14 with Holes
×4Technic, Axle 2L Notched
×3Technic, Brick 1 x 2 with Axle Hole
Technic, Plate 1 x 5 with Smooth Ends, 4 Studs and Center Axle Hole
×4Technic, Axle 5.5L with Stop
Technic, Liftarm Thick 1 x 5
×2Technic, Liftarm Thin 1 x 4 - Axle Holes
×2Technic, Pin without Friction Ridges
×3Technic, Brick 1 x 2 with Hole
×2Technic, Brick 1 x 4 with Holes
×2Slope, Inverted 33 3 x 2 with Flat Bottom Pin and Connections between Studs
Technic, Axle 1L with Pin without Friction Ridges with Round Hole
×2Dish 4 x 4 Inverted (Radar) with Solid Stud
Brick, Modified 1 x 1 with Headlight
×10Technic, Liftarm Thin 1 x 2 - Axle Holes
×2Slope, Curved 6 x 1 Inverted
×2Wheel 11mm D. x 8mm with Center Groove, 4 Spokes
Technic Bush 1/2 Smooth
×3Slope, Inverted 33 3 x 1
×2Technic, Axle 1L with Pin with Friction Ridges
×2Wedge 4 x 4 (Slope 18 Corner)
×2Wedge, Plate 3 x 2 Right
×3Wedge, Plate 3 x 2 Left
×3Slope 75 2 x 1 x 3 - Hollow Stud
×4Plate, Modified 1 x 8 with Door Rail
×2Wedge, Plate 12 x 3 Left
×2Wedge, Plate 12 x 3 Right
×2Slope, Curved 2 x 2 x 2/3 with 2 Studs and Curved Sides
×3Plate, Modified 1 x 2 with Bar Handle on Side - Closed Ends
×13Wedge 6 x 4 Triple Inverted with Connections between 4 Studs
Bar 1L with Clip Mechanical Claw - Cut Edges and Hole on Side
×2Wedge 4 x 4 Triple with Stud Notches
Plate, Modified 1 x 1 with Tooth Horizontal
×2Brick, Modified 1 x 2 with Studs on 2 Sides
Wedge, Plate 6 x 3 Right
×3Wedge, Plate 6 x 3 Left
×3Wheel 43.2mm D. x 26mm Technic Racing Small, 6 Pin Holes
Plate, Modified 1 x 2 with 2 Open O Clips (Horizontal Grip)
×2Wedge, Plate 6 x 6 Cut Corner
×2Tire 24mm D. x 7mm Offset Tread - Band Around Center of Tread
×2Hinge Brick 2 x 2 Top Plate
×2Wedge 6 x 4 Cutout with Stud Notches
Plate, Modified 1 x 2 with Clip on End (Horizontal Grip)
×8Technic, Axle and Pin Connector Perpendicular
×3Technic, Brick 1 x 1 with Hole
×2Technic, Pin 3L with Friction Ridges
×2Technic, Liftarm Thin 1 x 3 - Axle Holes
×2Brick, Modified 1 x 1 with Stud on Side
×2Plate, Modified 4 x 6 with Trap Door Hinge (Long Pins)
Windscreen 6 x 4 x 2 Round with Bar Handle
×2Plate, Modified 1 x 2 with Clip with Center Cut on Top
×4Tire 17.5mm D. x 6mm with Shallow Staggered Treads - Band Around Center of Tread
Plate, Modified 1 x 4 with 2 Studs without Groove
×2Slope, Curved 4 x 1 x 2/3 Double
Plate, Modified 2 x 2 x 2/3 with 2 Studs on Side
×4Bracket 1 x 2 - 2 x 2 Inverted
×7Bracket 1 x 2 - 1 x 2 Inverted
×2